NSN 5990-00-010-1413 · NIIN 000101413 · FSC 5990
NO DASHES 5990000101413
In Stock
SYNCHRO,TRANSMITTER
Synchros and Resolvers
Technical characteristics
49 rows
Straight from the federal item record. Entries the record leaves empty are shown empty — nothing is filled in on its behalf.
| MRC | Requirement | Value |
|---|---|---|
| CSJY | TRANSFORMATION RATIO | ROTOR TO STATOR NOMINAL 0.454 |
| CRSJ | SHAFT TYPE | SINGLE SHAFT ROUND, TAPERED, THREADED, UNDERCUT |
| CRSY | ALIGNMENT HOLE DEPTH | INCHES MAXIMUM 0.0900 |
| CRGZ | PLUS J ZSO REACTANCE IN OHMS | NOMINAL 28.00 |
| CRJX | SHAFT TAPERED END MINOR DIAMETER | SINGLE SHAFT INCHES NOMINAL 0.0780 |
| CQXQ | PLUS J ZRO REACTANCE IN OHMS | NOMINAL 243.00 |
| AJWX | MOUNTING SURFACE TO TERMINAL END DISTANCE | INCHES NOMINAL 1.6200 |
| AJYY | SHAFT THREAD SERIES DESIGNATOR | SINGLE SHAFT UNF |
| AKAF | SHAFT THREAD DIRECTION | SINGLE SHAFT RIGHT-HAND |
| AKAN | SHAFT THREAD CLASS | 3A |
| CQRG | BODY MATERIAL | STEEL CORROSION RESISTING |
| CQTM | TERMINAL LOCATION | REAR |
| AFJN | FRAGILITY FACTOR | MODERATELY RUGGED |
| AJSL | BODY SIZE | 11 |
| AJSR | ROTOR INPUT VOLTAGE RATING IN VOLTS | NOMINAL 26.0 |
| AJSS | FREQUENCY IN HERTZ | NOMINAL 400.0 |
| AJST | ROTOR INPUT CURRENT RATING | MILLIAMPERES MAXIMUM 120.0 |
| AJSV | ROTOR INPUT ELECTRICAL POWER RATING | MILLIWATTS MAXIMUM 600.0 |
| AJSW | ZRO RESISTANCE IN OHMS | NOMINAL 44.00 |
| AJSY | ZSO RESISTANCE IN OHMS | NOMINAL 57.00 |
| AJTS | ROTOR DC RESISTANCE IN OHMS | NOMINAL 18.00 |
| AJTT | STATOR DC RESISTANCE IN OHMS | NOMINAL 9.30 |
| AJVF | PHASE SHIFT ANGLE IN DEG | INPUT TO OUTPUT NOMINAL 4.000 |
| AJVH | MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 25.00 |
| AJVL | ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -15.0 TO 15.0 |
| AJVS | ACTUATOR FRICTION TORQUE AT MINUS 55 DEG CELSIUS | CENTIMETER-GRAMS MAXIMUM 1.8 |
| AJVT | ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS | CENTIMETER-GRAMS MAXIMUM 0.6 |
| AJVV | TORQUE GRADIENT PER ANGULAR DEG | MILLIMETER-MILLIGRAMS MINIMUM 2000.0 |
| AJVW | ALIGNMENT HOLE QUANTITY | 4 |
| AJWQ | PILOT LENGTH | INCHES MINIMUM 0.0590 AND INCHES MAXIMUM 0.0650 |
| AAQL | BODY STYLE | |
| AAVH | SHOULDER DIAMETER | INCHES MINIMUM 0.9995 AND INCHES MAXIMUM 1.0000 |
| AAVL | PILOT DIAMETER | INCHES MINIMUM 0.6245 AND INCHES MAXIMUM 0.6250 |
| ABHP | OVERALL LENGTH | INCHES MINIMUM 1.9800 AND INCHES MAXIMUM 2.0100 |
| ABKK | FLANGE DIAMETER | INCHES MINIMUM 1.0590 AND INCHES MAXIMUM 1.0620 |
| ABKU | FLANGE THICKNESS | INCHES MINIMUM 0.0900 AND INCHES MAXIMUM 0.0960 |
| ABPA | UNDERCUT DIAMETER | INCHES NOMINAL 0.9750 |
| ABPC | UNDERCUT WIDTH | INCHES NOMINAL 0.0500 |
| ABRY | LENGTH | SHOULDER INCHES MINIMUM 0.0590 AND INCHES MAXIMUM 0.0650 |
| ABWV | SHAFT DIAMETER | SINGLE SHAFT INCHES MINIMUM 0.0800 AND INCHES MAXIMUM 0.0810 |
| ABXF | SHAFT LENGTH | SINGLE SHAFT INCHES MINIMUM 0.3600 AND INCHES MAXIMUM 0.3900 |
| AEDC | SHAFT UNDERCUT WIDTH | SINGLE SHAFT INCHES NOMINAL 0.0300 |
| CSLT | SHAFT TAPER ANGLE IN DEG | 3.0 |
| CTBP | SHAFT TIP LENGTH | SINGLE SHAFT INCHES NOMINAL 0.0650 |
| CTCW | ALIGNMENT HOLE BOLT CIRCLE DIAMETER | INCHES MINIMUM 0.8090 AND INCHES MAXIMUM 0.8150 |
| CWAC | SHAFT TAPER LENGTH | SINGLE SHAFT INCHES NOMINAL 0.1370 |
| CWBH | SHAFT NOMINAL THREAD SIZE | SINGLE SHAFT INCHES 0.060 |
| CWJD | SHAFT UNDERCUT DIAMETER | SINGLE SHAFT INCHES MINIMUM 0.0440 AND INCHES MAXIMUM 0.0460 |
| TTQY | TERMINAL TYPE AND QUANTITY | WIRE LEAD 5 |
Supersedes
This item replaces cancelled NIIN 008838548. An older drawing citing one of those numbers resolves here.