NSN 5905-00-079-6336 · NIIN 000796336 · FSC 5905
NO DASHES 5905000796336
In Stock
RESISTOR,VARIABLE,WIRE WOUND,NON
Resistor
Technical characteristics
28 rows
Straight from the federal item record. Entries the record leaves empty are shown empty — nothing is filled in on its behalf.
| MRC | Requirement | Value |
|---|---|---|
| AEFD | ACTUATOR TYPE | SINGLE SHAFT |
| AEDX | SHAFT STYLE | |
| AGTP | LATERAL DISTANCE BETWEEN MOUNTING HOLE CENTERS | INCHES NOMINAL 0.419 |
| AXGY | MOUNTING METHOD | TERMINAL |
| CQCC | ELECTRICAL RESISTANCE PER SECTION | KILOHMS SINGLE SECTION 1.0 |
| CQCM | CENTER TO CENTER DISTANCE BETWEEN CENTER TERMINAL AND OUTSIDE TERMINAL | INCHES MINIMUM 0.095 AND INCHES MAXIMUM 0.105 |
| CQGN | AMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER | SINGLE SECTION 150.0 |
| CQTM | TERMINAL LOCATION | LOCATION NOT OTHERWISE SPECIFIED REAR END |
| CRFJ | TEMP COEFFICIENT OF RESISTANCE PER SECTION IN PPM PER DEG CELSIUS | SINGLE SECTION -50.0 TO 50.0 |
| AEHT | CENTER TO CENTER DISTANCE BETWEEN TERMINALS | INCHES MINIMUM 0.095 AND INCHES MAXIMUM 0.105 |
| ADAQ | BODY LENGTH | INCHES MINIMUM 0.360 AND INCHES MAXIMUM 0.390 |
| ADAT | BODY WIDTH | INCHES MINIMUM 0.145 AND INCHES MAXIMUM 0.245 |
| ADAU | BODY HEIGHT | INCHES MINIMUM 0.360 AND INCHES MAXIMUM 0.390 |
| CSDH | AMBIENT TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER | SINGLE SECTION 85.0 |
| TEST | TEST DATA DOCUMENT | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--IL-R-27208 |
| TTQY | TERMINAL TYPE AND QUANTITY | PIN 3 |
| ZZZK | SPECIFICATION/STANDARD DATA | GOVERNMENT SPECIFICATION 81349--IL-R-27208 TO 9 |
| ABJT | TERMINAL LENGTH | INCHES MINIMUM 0.172 |
| ABKW | OVERALL HEIGHT | INCHES MINIMUM 0.360 AND INCHES MAXIMUM 0.390 |
| ABMK | OVERALL WIDTH | INCHES MINIMUM 0.145 AND INCHES MAXIMUM 0.245 |
| ABWV | SHAFT DIAMETER | INCHES MINIMUM 0.050 AND INCHES MAXIMUM 0.100 |
| ABXF | SHAFT LENGTH | INCHES MAXIMUM 0.080 |
| ABHP | OVERALL LENGTH | INCHES MINIMUM 0.612 AND INCHES MAXIMUM 0.642 |
| AAQL | BODY STYLE | |
| AARG | RELIABILITY INDICATOR | NOT ESTABLISHED |
| CRSS | RESISTANCE TOLERANCE PER SECTION IN PERCENT | SINGLE SECTION -5.0 TO 5.0 |
| AAPN | SECTION QUANTITY | 1 |
| CRGD | POWER DISSIPATION RATING PER SECTION IN WATTS | FREE AIR SINGLE SECTION 0.8 |
Supersedes
This item replaces cancelled NIIN 001037762. An older drawing citing one of those numbers resolves here.