NSN 5990-00-988-7902 · NIIN 009887902 · FSC 5990
NO DASHES 5990009887902
In Stock
SYNCHRO,CONTROL TRANSFORMER
Synchros and Resolvers
Technical characteristics
46 rows
Straight from the federal item record. Entries the record leaves empty are shown empty — nothing is filled in on its behalf.
| MRC | Requirement | Value |
|---|---|---|
| CQWQ | SHAFT THREAD LENGTH | SINGLE SHAFT INCHES NOMINAL 0.2000 |
| CQTM | TERMINAL LOCATION | REAR |
| CSJY | TRANSFORMATION RATIO | ROTOR TO STATOR NOMINAL 0.783 |
| AJTG | ZRO IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 2875.00 AND MAXIMUM 3375.00 |
| AJTH | ZRO IMPEDANCE ANGLE IN DEG | MINIMUM 76.00 AND MAXIMUM 80.00 |
| AJTN | ZSS IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 660.00 AND MAXIMUM 810.00 |
| AJTP | ZSS IMPEDANCE ANGLE IN DEG | MINIMUM 9.00 AND MAXIMUM 13.00 |
| AAQL | BODY STYLE | |
| AAVH | SHOULDER DIAMETER | INCHES MINIMUM 1.5615 AND INCHES MAXIMUM 1.5620 |
| AAVL | PILOT DIAMETER | INCHES MINIMUM 0.9370 AND INCHES MAXIMUM 0.9375 |
| ABHP | OVERALL LENGTH | INCHES NOMINAL 3.0600 |
| ABKK | FLANGE DIAMETER | INCHES MINIMUM 1.7450 AND INCHES MAXIMUM 1.7500 |
| ABKU | FLANGE THICKNESS | INCHES NOMINAL 0.0930 |
| ABPA | UNDERCUT DIAMETER | INCHES NOMINAL 1.6250 |
| CRSJ | SHAFT TYPE | SINGLE SHAFT SPLINE W/THREADS |
| CRSY | ALIGNMENT HOLE DEPTH | INCHES MINIMUM 0.1250 |
| AJSS | FREQUENCY IN HERTZ | NOMINAL 60.0 |
| ZZZK | SPECIFICATION/STANDARD DATA | GOVERNMENT SPECIFICATION 81349--IL-S-20708 TO 33 |
| ABPC | UNDERCUT WIDTH | INCHES NOMINAL 0.0780 |
| ABRY | LENGTH | SHOULDER INCHES NOMINAL 0.1320 |
| ABWV | SHAFT DIAMETER | SINGLE SHAFT INCHES MINIMUM 0.1870 AND INCHES MAXIMUM 0.1872 |
| ABXF | SHAFT LENGTH | SINGLE SHAFT INCHES NOMINAL 0.5400 |
| AFJN | FRAGILITY FACTOR | MODERATELY RUGGED |
| AHCG | MAXIMUM TEMP RISE | CELSIUS 25.0 |
| AJSL | BODY SIZE | 18 |
| AJSN | STATOR INPUT VOLTAGE RATING IN VOLTS | NOMINAL 115.0 |
| AJSP | STATOR INPUT CURRENT RATING | MILLIAMPERES MAXIMUM 40.0 |
| AJSQ | STATOR INPUT ELECTRICAL POWER RATING | MILLIWATTS NOMINAL 950.0 |
| CTCW | ALIGNMENT HOLE BOLT CIRCLE DIAMETER | INCHES NOMINAL 1.2500 |
| AJVF | PHASE SHIFT ANGLE IN DEG | INPUT TO OUTPUT NOMINAL 11.000 |
| AJVG | MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | OUTPUT 30.00 |
| AJVM | SPLINE TOOTH QUANTITY | 21 |
| AJVV | TORQUE GRADIENT PER ANGULAR DEG | INCH-OUNCES MAXIMUM 0.100 |
| AJYY | SHAFT THREAD SERIES DESIGNATOR | SINGLE SHAFT UNF |
| TEST | TEST DATA DOCUMENT | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--IL-S-20708 |
| AJVH | MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 85.00 |
| AJVL | ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -8.0 TO 8.0 |
| AKAF | SHAFT THREAD DIRECTION | SINGLE SHAFT RIGHT-HAND |
| CWBH | SHAFT NOMINAL THREAD SIZE | SINGLE SHAFT INCHES 0.190 |
| MATT | MATERIAL | BODY STEEL CORROSION RESISTING |
| AJVW | ALIGNMENT HOLE QUANTITY | 4 |
| AJWQ | PILOT LENGTH | INCHES NOMINAL 0.0400 |
| AJWX | MOUNTING SURFACE TO TERMINAL END DISTANCE | INCHES NOMINAL 2.5200 |
| AJXA | SPLINE TOOTH DIAMETRAL PITCH | 120 |
| AKAN | SHAFT THREAD CLASS | 2A |
| TTQY | TERMINAL TYPE AND QUANTITY | SCREW 5 |
Supersedes
This item replaces cancelled NIIN 011623450. An older drawing citing one of those numbers resolves here.