RESISTOR,VARIABLE,WIRE WOUND,PRE
Resistor
Technical characteristics
39 rows
Straight from the federal item record. Entries the record leaves empty are shown empty — nothing is filled in on its behalf.
| MRC | Requirement | Value |
|---|---|---|
| CQFL | FUNCTION CONFORMITY TOLERANCE PER SECTION | SINGLE SECTION -0.50 TO 0.50 |
| CQGN | AMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER | SINGLE SECTION 105.0 |
| CQCC | ELECTRICAL RESISTANCE PER SECTION | KILOHMS SINGLE SECTION 5.0 |
| CQCK | ROTARY ACTUATOR TRAVEL IN ANGULAR DEG | NOMINAL 360.0 |
| AEFH | EFFECTIVE ELECTRICAL ROTATION IN DEG ANGULAR ROTATION | MINIMUM 319.0 AND MAXIMUM 321.0 |
| AEFK | MAXIMUM STARTING TORQUE | INCH-OUNCES 0.60 |
| AEFY | SHAFT END PLAY | INCHES 0.006 |
| AEGA | LATERAL RUNOUT | INCHES 0.001 |
| AEGB | PILOT DIAMETER RUNOUT | INCHES 0.001 |
| AXGY | MOUNTING METHOD | CLAMP RING(S) |
| BYDT | BEARING TYPE | SHAFT BEARING |
| AAPN | SECTION QUANTITY | 1 |
| AAQL | BODY STYLE | |
| AARG | RELIABILITY INDICATOR | NOT ESTABLISHED |
| AAVL | PILOT DIAMETER | INCHES MINIMUM 1.9360 AND INCHES MAXIMUM 1.9370 |
| AAVM | PILOT LENGTH | INCHES MINIMUM 0.0290 AND INCHES MAXIMUM 0.0320 |
| ABHP | OVERALL LENGTH | INCHES MINIMUM 1.217 AND INCHES MAXIMUM 1.260 |
| CQTM | TERMINAL LOCATION | LOCATION NOT OTHERWISE SPECIFIED RADIALLY POSITIONED OVER LESS THAN HALF THE CIRCUMFERENCE |
| CRFJ | TEMP COEFFICIENT OF RESISTANCE PER SECTION IN PPM PER DEG CELSIUS | SINGLE SECTION -30.0 TO 30.0 |
| CRGD | POWER DISSIPATION RATING PER SECTION IN WATTS | FREE AIR SINGLE SECTION 4.0 |
| CRGM | FUNCTION CONFORMITY PER SECTION | SINGLE SECTION INDEPENDENT LINEARITY |
| CRSS | RESISTANCE TOLERANCE PER SECTION IN PERCENT | SINGLE SECTION -1.0 TO 1.0 |
| CRSX | ACTUATOR TRAVEL CONTROL FEATURE | CONTINUOUS MOTION |
| CSBX | FUNCTION CHARACTERISTIC PER SECTION | SINGLE SECTION LINEAR |
| CSDH | AMBIENT TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER | SINGLE SECTION 40.0 |
| TEST | TEST DATA DOCUMENT | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--IL-R-8903 |
| TTQY | TERMINAL TYPE AND QUANTITY | SOLDER STUD 12 |
| ZZZK | SPECIFICATION/STANDARD DATA | GOVERNMENT SPECIFICATION 81349--IL-R-8903 |
| AEDX | SHAFT STYLE | |
| AEFD | ACTUATOR TYPE | SINGLE SHAFT |
| AEDA | MOUNTING LIP DEPTH | INCHES MINIMUM 0.0680 AND INCHES MAXIMUM 0.0850 |
| ADAV | OVERALL DIAMETER | INCHES MINIMUM 2.099 AND INCHES MAXIMUM 2.151 |
| AECZ | MOUNTING LIP DIAMETER | INCHES MINIMUM 1.9900 AND INCHES MAXIMUM 2.0100 |
| ADAQ | BODY LENGTH | INCHES MINIMUM 0.990 AND INCHES MAXIMUM 1.010 |
| ABXF | SHAFT LENGTH | INCHES MINIMUM 0.198 AND INCHES MAXIMUM 0.218 |
| ABWV | SHAFT DIAMETER | INCHES MAXIMUM 0.250 |
| ABPA | UNDERCUT DIAMETER | INCHES MINIMUM 1.9375 AND INCHES MAXIMUM 1.9385 |
| ABPC | UNDERCUT WIDTH | INCHES MINIMUM 0.0700 AND INCHES MAXIMUM 0.0900 |
| ABPM | BODY DIAMETER | INCHES MINIMUM 1.990 AND INCHES MAXIMUM 2.010 |
Supersedes
This item replaces cancelled NIINs 002012806 · 002575836 · 002575823 · 002837068 · 002838396 · 002838851 · 002837072 · 002834488 · 002843835 · 002833696 · 002837073 · 002837054 · 002838400 · 002837013 · 002954054 · 002834489 · 002834480 · 002837075 · 004751927 · 005027883 · 005037425 · 005027881 · 005188295 · 005027882 · 005492014 · 005563231 · 005565144 · 005394201 · 005565240 · 005539712 · 005539713 · 005497152 · 005539714 · 006659404 · 006659863 · 006661964 · 006659868 · 006659856 · 006659878 · 006659363 · 006660144 · 006435649 · 006610582 · 006365619 · 006659865 · 006815339 · 006888082 · 006811053 · 007407942. An older drawing citing one of those numbers resolves here.