NSN 5905-00-232-1830 · NIIN 002321830 · FSC 5905
NO DASHES 5905002321830
In Stock
RESISTOR,VARIABLE,WIRE WOUND,PRE
Resistor
Technical characteristics
26 rows
Straight from the federal item record. Entries the record leaves empty are shown empty — nothing is filled in on its behalf.
| MRC | Requirement | Value |
|---|---|---|
| ABPA | UNDERCUT DIAMETER | INCHES MAXIMUM 0.975 |
| AAQL | BODY STYLE | |
| ADAQ | BODY LENGTH | INCHES MAXIMUM 2.093 |
| AECZ | MOUNTING LIP DIAMETER | INCHES NOMINAL 1.0620 |
| AAPN | SECTION QUANTITY | 5 |
| CQTM | TERMINAL LOCATION | LOCATION NOT OTHERWISE SPECIFIED RADIALLY POSITIONED OVER LESS THAN HALF THE CIRCUMFERENCE |
| CQCC | ELECTRICAL RESISTANCE PER SECTION | KILOHMS 1ST SECTION 10.0 AND KILOHMS 2ND SECTION 10.0 AND KILOHMS 3RD SECTION 10.0 AND KILOHMS 4TH SECTION 5.0 AND KILOHMS 5TH SECTION 10.0 |
| ABPC | UNDERCUT WIDTH | INCHES MINIMUM 0.0570 |
| AEDX | SHAFT STYLE | |
| ABWV | SHAFT DIAMETER | INCHES MINIMUM 0.1244 AND INCHES MAXIMUM 0.1247 |
| AAVM | PILOT LENGTH | INCHES NOMINAL 0.0620 |
| CSBX | FUNCTION CHARACTERISTIC PER SECTION | ALL SECTIONS TABLE |
| PRPY | PROPRIETARY CHARACTERISTICS | PACS |
| TEST | TEST DATA DOCUMENT | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) 55972-1960932 |
| TTQY | TERMINAL TYPE AND QUANTITY | TURRET 15 |
| ABPM | BODY DIAMETER | INCHES MAXIMUM 1.094 |
| AARG | RELIABILITY INDICATOR | NOT ESTABLISHED |
| AAVL | PILOT DIAMETER | INCHES MINIMUM 0.9683 AND INCHES MAXIMUM 0.9688 |
| AEFD | ACTUATOR TYPE | SINGLE SHAFT |
| CQFL | FUNCTION CONFORMITY TOLERANCE PER SECTION | 1ST SECTION -0.25 TO 0.25 AND 2ND SECTION -0.20 TO 0.20 AND 3RD SECTION -0.20 TO 0.20 AND 4TH SECTION -0.50 TO 0.50 AND 5TH SECTION -0.20 TO 0.20 |
| ABXF | SHAFT LENGTH | INCHES MINIMUM 0.480 AND INCHES MAXIMUM 0.520 |
| CRGD | POWER DISSIPATION RATING PER SECTION IN WATTS | FREE AIR ALL SECTIONS 2.0 |
| CRGM | FUNCTION CONFORMITY PER SECTION | ALL SECTIONS ABSOLUTE CONFORMITY |
| CRSS | RESISTANCE TOLERANCE PER SECTION IN PERCENT | 1ST SECTION -5.0 TO 5.0 AND 2ND SECTION -5.0 TO 5.0 AND 3RD SECTION -5.0 TO 5.0 AND 4TH SECTION -10.0 TO 10.0 AND 5TH SECTION -10.0 TO 10.0 |
| AXGY | MOUNTING METHOD | CLAMP RING(S) |
| AEDA | MOUNTING LIP DEPTH | INCHES NOMINAL 0.0620 |