NSN 5905-00-725-0497 · NIIN 007250497 · FSC 5905
NO DASHES 5905007250497
In Stock
RESISTOR,VARIABLE,WIRE WOUND,NON
Resistor
Technical characteristics
28 rows
Straight from the federal item record. Entries the record leaves empty are shown empty — nothing is filled in on its behalf.
| MRC | Requirement | Value |
|---|---|---|
| ABXF | SHAFT LENGTH | INCHES MINIMUM 0.844 AND INCHES MAXIMUM 0.906 |
| ADAQ | BODY LENGTH | INCHES NOMINAL 0.625 |
| AEFD | ACTUATOR TYPE | SINGLE SHAFT |
| CQPH | DEVICE DESIGN TYPE | LOCATION NOT OTHERWISE SPECIFIED AT 9:00 OCLOCK |
| CQTM | TERMINAL LOCATION | LOCATION NOT OTHERWISE SPECIFIED RADIALLY POSITIONED OVER LESS THAN HALF THE CIRCUMFERENCE |
| CRGD | POWER DISSIPATION RATING PER SECTION IN WATTS | FREE AIR SINGLE SECTION 4.0 |
| CRSS | RESISTANCE TOLERANCE PER SECTION IN PERCENT | SINGLE SECTION -10.0 TO 10.0 |
| CRSX | ACTUATOR TRAVEL CONTROL FEATURE | STOPS |
| AEDX | SHAFT STYLE | |
| AARG | RELIABILITY INDICATOR | NOT ESTABLISHED |
| ABPM | BODY DIAMETER | INCHES MINIMUM 1.500 AND INCHES MAXIMUM 1.710 |
| ADAP | MOUNTING BUSHING LENGTH | INCHES MINIMUM 0.360 AND INCHES MAXIMUM 0.390 |
| AAPN | SECTION QUANTITY | 1 |
| AEFP | NONTURN DEVICE RADIUS | INCHES MINIMUM 0.516 AND INCHES MAXIMUM 0.546 |
| AJYN | SCREW THREAD DIAMETER | INCHES NOMINAL 0.375 |
| AJYP | SCREW THREAD SERIES DESIGNATOR | UNEF |
| AJYQ | SCREW THREAD QUANTITY PER INCH | 32.0 |
| AXGY | MOUNTING METHOD | STANDARD BUSHING |
| CQCC | ELECTRICAL RESISTANCE PER SECTION | KILOHMS SINGLE SECTION 25.000 |
| CQCK | ROTARY ACTUATOR TRAVEL IN ANGULAR DEG | MINIMUM 280.0 AND MAXIMUM 305.0 |
| CQGN | AMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER | SINGLE SECTION 105.0 |
| ZZZK | SPECIFICATION/STANDARD DATA | GOVERNMENT SPECIFICATION 81349--IL-R-19 TO 3 |
| ABWV | SHAFT DIAMETER | INCHES MINIMUM 0.248 AND INCHES MAXIMUM 0.251 |
| CSDH | AMBIENT TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER | SINGLE SECTION 40.0 |
| FEAT | SPECIAL FEATURES | MOUNTING METHOD: STANDARD BUSHING W/PANEL SEAL AND STANDARD BUSHING W/SHAFT SEAL |
| TEST | TEST DATA DOCUMENT | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--IL-R-19 |
| TTQY | TERMINAL TYPE AND QUANTITY | TAB, SOLDER LUG 3 |
| AAQL | BODY STYLE |
Cross-references
4 manufacturer part numbers on file for this NSN — each shown against the CAGE code it belongs to.
| Manufacturer part number | CAGE |
|---|---|
| RA30SASD253A | 81349 |
| MIL-R-19/3 | 81349 |
| MIL-PRF-19/3 | 81349 |
| 5905PL1380530 | 9009H |