NSN 5990-00-477-1362 · NIIN 004771362 · FSC 5990
NO DASHES 5990004771362
In Stock
SYNCHRO,TRANSMITTER
Synchros and Resolvers
Technical characteristics
41 rows
Straight from the federal item record. Entries the record leaves empty are shown empty — nothing is filled in on its behalf.
| MRC | Requirement | Value |
|---|---|---|
| AJST | ROTOR INPUT CURRENT RATING | MILLIAMPERES MAXIMUM 31.0 |
| AJSV | ROTOR INPUT ELECTRICAL POWER RATING | MILLIWATTS NOMINAL 490.0 |
| AJTG | ZRO IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 3720.00 AND MAXIMUM 4700.00 |
| ABHP | OVERALL LENGTH | INCHES NOMINAL 2.2930 |
| ABKK | FLANGE DIAMETER | INCHES MINIMUM 1.0575 AND INCHES MAXIMUM 1.0620 |
| ABKU | FLANGE THICKNESS | INCHES NOMINAL 0.0930 |
| ABPA | UNDERCUT DIAMETER | INCHES NOMINAL 0.9750 |
| AHCG | MAXIMUM TEMP RISE | CELSIUS 20.0 |
| CQZS | SHAFT SLOT DEPTH | SINGLE SHAFT INCHES NOMINAL 0.0250 |
| CRHN | SHAFT SLOT WIDTH | SINGLE SHAFT INCHES NOMINAL 0.0200 |
| AJSS | FREQUENCY IN HERTZ | NOMINAL 400.0 |
| TTQY | TERMINAL TYPE AND QUANTITY | WIRE LEAD 5 |
| ZZZK | SPECIFICATION/STANDARD DATA | GOVERNMENT SPECIFICATION 81349--IL-S-20708 TO 2 |
| AFJN | FRAGILITY FACTOR | MODERATELY RUGGED |
| CSJY | TRANSFORMATION RATIO | STATOR TO ROTOR NOMINAL 0.783 |
| CTCW | ALIGNMENT HOLE BOLT CIRCLE DIAMETER | INCHES NOMINAL 0.8120 |
| AJSL | BODY SIZE | 11 |
| AJSR | ROTOR INPUT VOLTAGE RATING IN VOLTS | NOMINAL 115.0 |
| AAQL | BODY STYLE | |
| AAVH | SHOULDER DIAMETER | INCHES MINIMUM 0.9995 AND INCHES MAXIMUM 1.0000 |
| AAVL | PILOT DIAMETER | INCHES MINIMUM 0.6245 AND INCHES MAXIMUM 0.6250 |
| AJTH | ZRO IMPEDANCE ANGLE IN DEG | MINIMUM 80.00 AND MAXIMUM 84.00 |
| AJTN | ZSS IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 410.00 AND MAXIMUM 500.00 |
| AJTP | ZSS IMPEDANCE ANGLE IN DEG | MINIMUM 17.00 AND MAXIMUM 26.00 |
| AJVF | PHASE SHIFT ANGLE IN DEG | INPUT TO OUTPUT NOMINAL 4.500 |
| AJVG | MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | OUTPUT 45.00 |
| AJVH | MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 75.00 |
| AJVW | ALIGNMENT HOLE QUANTITY | 4 |
| AJWQ | PILOT LENGTH | INCHES NOMINAL 0.0620 |
| AJWX | MOUNTING SURFACE TO TERMINAL END DISTANCE | INCHES NOMINAL 1.7940 |
| CQRG | BODY MATERIAL | STEEL CORROSION RESISTING |
| CQTM | TERMINAL LOCATION | REAR |
| ABPC | UNDERCUT WIDTH | INCHES NOMINAL 0.0620 |
| AJVL | ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -7.0 TO 7.0 |
| AJVT | ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS | INCH-OUNCES MAXIMUM 0.07 |
| CRSY | ALIGNMENT HOLE DEPTH | INCHES MINIMUM 0.1250 |
| ABWV | SHAFT DIAMETER | SINGLE SHAFT INCHES MINIMUM 0.1198 AND INCHES MAXIMUM 0.1200 |
| ABXF | SHAFT LENGTH | SINGLE SHAFT INCHES NOMINAL 0.4990 |
| ABRY | LENGTH | SHOULDER INCHES NOMINAL 0.0620 |
| TEST | TEST DATA DOCUMENT | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--ILS-20708 |
| CRSJ | SHAFT TYPE | SINGLE SHAFT ROUND, SLOTTED |
Cross-references
8 manufacturer part numbers on file for this NSN — each shown against the CAGE code it belongs to.
| Manufacturer part number | CAGE |
|---|---|
| MIL-S-20708/2 | 81349 |
| 11CX4E | 81349 |
| M20708/2-04E | 81349 |
| CR40913002 | 05088 |
| AS20708/2 | 0VH01 |
| SAE-AS20708/2 | 0U583 |
| M20708/2-04E | 0U583 |
| 11CX1346-4 | 14404 |