NSN 5990-00-482-7927 · NIIN 004827927 · FSC 5990
NO DASHES 5990004827927
In Stock
SYNCHRO,TRANSMITTER
Synchros and Resolvers
Technical characteristics
44 rows
Straight from the federal item record. Entries the record leaves empty are shown empty — nothing is filled in on its behalf.
| MRC | Requirement | Value |
|---|---|---|
| AJTG | ZRO IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 1045.00 AND MAXIMUM 1400.00 |
| AJTH | ZRO IMPEDANCE ANGLE IN DEG | MINIMUM 84.00 AND MAXIMUM 87.50 |
| AJTN | ZSS IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 40.00 AND MAXIMUM 57.00 |
| AJTP | ZSS IMPEDANCE ANGLE IN DEG | MINIMUM 34.00 AND MAXIMUM 48.00 |
| AJVF | PHASE SHIFT ANGLE IN DEG | INPUT TO OUTPUT NOMINAL 1.500 |
| AJSV | ROTOR INPUT ELECTRICAL POWER RATING | MILLIWATTS NOMINAL 900.0 |
| AJST | ROTOR INPUT CURRENT RATING | MILLIAMPERES MAXIMUM 110.0 |
| AJSR | ROTOR INPUT VOLTAGE RATING IN VOLTS | NOMINAL 115.0 |
| AJSS | FREQUENCY IN HERTZ | NOMINAL 400.0 |
| AAQL | BODY STYLE | |
| AAVH | SHOULDER DIAMETER | INCHES MINIMUM 1.5615 AND INCHES MAXIMUM 1.5620 |
| AAVL | PILOT DIAMETER | INCHES MINIMUM 0.9370 AND INCHES MAXIMUM 0.9375 |
| ABHP | OVERALL LENGTH | INCHES NOMINAL 3.0600 |
| AHCG | MAXIMUM TEMP RISE | CELSIUS 20.0 |
| AJSL | BODY SIZE | 18 |
| CRSJ | SHAFT TYPE | SINGLE SHAFT SPLINE W/THREADS |
| CRSY | ALIGNMENT HOLE DEPTH | INCHES NOMINAL 0.1250 |
| CSJY | TRANSFORMATION RATIO | ROTOR TO STATOR NOMINAL 0.783 |
| CTCW | ALIGNMENT HOLE BOLT CIRCLE DIAMETER | INCHES NOMINAL 1.2500 |
| CWBH | SHAFT NOMINAL THREAD SIZE | SINGLE SHAFT INCHES 0.190 |
| TEST | TEST DATA DOCUMENT | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) 49956-C362032 |
| TTQY | TERMINAL TYPE AND QUANTITY | SCREW 5 |
| AJVG | MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | OUTPUT 40.00 |
| AJVH | MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 60.00 |
| AJVL | ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -6.0 TO 6.0 |
| AJVM | SPLINE TOOTH QUANTITY | 21 |
| ABKK | FLANGE DIAMETER | INCHES MINIMUM 1.7450 AND INCHES MAXIMUM 1.7500 |
| ABKU | FLANGE THICKNESS | INCHES NOMINAL 0.0930 |
| ABPA | UNDERCUT DIAMETER | INCHES NOMINAL 1.6250 |
| ABPC | UNDERCUT WIDTH | INCHES NOMINAL 0.0780 |
| ABRY | LENGTH | SHOULDER INCHES NOMINAL 0.1320 |
| ABWV | SHAFT DIAMETER | SINGLE SHAFT INCHES MINIMUM 0.1870 AND INCHES MAXIMUM 0.1872 |
| ABXF | SHAFT LENGTH | SINGLE SHAFT INCHES NOMINAL 0.5400 |
| CQTM | TERMINAL LOCATION | REAR |
| CQWQ | SHAFT THREAD LENGTH | SINGLE SHAFT INCHES NOMINAL 0.2000 |
| AKAF | SHAFT THREAD DIRECTION | SINGLE SHAFT RIGHT-HAND |
| AKAN | SHAFT THREAD CLASS | 2A |
| CQRG | BODY MATERIAL | STEEL CORROSION RESISTING |
| AJWX | MOUNTING SURFACE TO TERMINAL END DISTANCE | INCHES NOMINAL 2.5200 |
| AJXA | SPLINE TOOTH DIAMETRAL PITCH | 120 |
| AJYY | SHAFT THREAD SERIES DESIGNATOR | SINGLE SHAFT UNF |
| AJWQ | PILOT LENGTH | INCHES NOMINAL 0.0400 |
| AJVW | ALIGNMENT HOLE QUANTITY | 4 |
| AJVT | ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS | INCH-OUNCES MAXIMUM 0.10 |