NSN 5990-00-924-4165 · NIIN 009244165 · FSC 5990
NO DASHES 5990009244165
In Stock
SYNCHRO,TRANSMITTER
Synchros and Resolvers
Technical characteristics
46 rows
Straight from the federal item record. Entries the record leaves empty are shown empty — nothing is filled in on its behalf.
| MRC | Requirement | Value |
|---|---|---|
| AJWQ | PILOT LENGTH | INCHES NOMINAL 0.0620 |
| AJVW | ALIGNMENT HOLE QUANTITY | 4 |
| AJTH | ZRO IMPEDANCE ANGLE IN DEG | MINIMUM 80.00 AND MAXIMUM 84.00 |
| AJTN | ZSS IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 410.00 AND MAXIMUM 500.00 |
| AJTP | ZSS IMPEDANCE ANGLE IN DEG | MINIMUM 17.00 AND MAXIMUM 26.00 |
| AHCG | MAXIMUM TEMP RISE | CELSIUS 20.0 |
| AJSL | BODY SIZE | 11 |
| AJSR | ROTOR INPUT VOLTAGE RATING IN VOLTS | NOMINAL 115.0 |
| AJSS | FREQUENCY IN HERTZ | NOMINAL 400.0 |
| AJST | ROTOR INPUT CURRENT RATING | MILLIAMPERES MAXIMUM 31.0 |
| AJSV | ROTOR INPUT ELECTRICAL POWER RATING | MILLIWATTS NOMINAL 490.0 |
| AJTG | ZRO IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 3720.00 AND MAXIMUM 4700.00 |
| AKAN | SHAFT THREAD CLASS | 2A |
| CQRG | BODY MATERIAL | STEEL CORROSION RESISTING |
| CQTM | TERMINAL LOCATION | REAR |
| CQWQ | SHAFT THREAD LENGTH | SINGLE SHAFT INCHES NOMINAL 0.1900 |
| CRSJ | SHAFT TYPE | SINGLE SHAFT SPLINE W/THREADS |
| CRSY | ALIGNMENT HOLE DEPTH | INCHES MINIMUM 0.1250 |
| CSJY | TRANSFORMATION RATIO | STATOR TO ROTOR NOMINAL 0.783 |
| CTCW | ALIGNMENT HOLE BOLT CIRCLE DIAMETER | INCHES NOMINAL 0.8120 |
| CWBH | SHAFT NOMINAL THREAD SIZE | SINGLE SHAFT INCHES 0.190 |
| TEST | TEST DATA DOCUMENT | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--IL-S-20708 |
| TTQY | TERMINAL TYPE AND QUANTITY | SCREW 5 |
| ZZZK | SPECIFICATION/STANDARD DATA | GOVERNMENT SPECIFICATION 81349--IL-S-20708 TO 2 |
| AJYY | SHAFT THREAD SERIES DESIGNATOR | SINGLE SHAFT UNF |
| AKAF | SHAFT THREAD DIRECTION | SINGLE SHAFT RIGHT-HAND |
| AAQL | BODY STYLE | |
| AAVH | SHOULDER DIAMETER | INCHES MINIMUM 0.9995 AND INCHES MAXIMUM 1.0000 |
| AJVL | ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -7.0 TO 7.0 |
| AJVF | PHASE SHIFT ANGLE IN DEG | INPUT TO OUTPUT NOMINAL 4.500 |
| AJVG | MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | OUTPUT 45.00 |
| AJVH | MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 75.00 |
| ABXF | SHAFT LENGTH | SINGLE SHAFT INCHES NOMINAL 0.5620 |
| AFJN | FRAGILITY FACTOR | MODERATELY RUGGED |
| AJXA | SPLINE TOOTH DIAMETRAL PITCH | 120 |
| ABPC | UNDERCUT WIDTH | INCHES NOMINAL 0.0620 |
| ABRY | LENGTH | SHOULDER INCHES NOMINAL 0.0620 |
| AJVM | SPLINE TOOTH QUANTITY | 21 |
| AJVT | ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS | INCH-OUNCES MAXIMUM 0.07 |
| ABPA | UNDERCUT DIAMETER | INCHES NOMINAL 0.9750 |
| ABKK | FLANGE DIAMETER | INCHES MINIMUM 1.0570 AND INCHES MAXIMUM 1.0620 |
| ABKU | FLANGE THICKNESS | INCHES NOMINAL 0.0930 |
| ABWV | SHAFT DIAMETER | SINGLE SHAFT INCHES MINIMUM 0.1870 AND INCHES MAXIMUM 0.1872 |
| AAVL | PILOT DIAMETER | INCHES MINIMUM 0.6245 AND INCHES MAXIMUM 0.6250 |
| ABHP | OVERALL LENGTH | INCHES NOMINAL 2.3560 |
| AJWX | MOUNTING SURFACE TO TERMINAL END DISTANCE | INCHES MAXIMUM 1.7940 |
Supersedes
This item replaces cancelled NIINs 001659107 · 012816428. An older drawing citing one of those numbers resolves here.