NSN 5990-00-924-4164 · NIIN 009244164 · FSC 5990
NO DASHES 5990009244164
In Stock
SYNCHRO,TRANSMITTER
Synchros and Resolvers
Technical characteristics
46 rows
Straight from the federal item record. Entries the record leaves empty are shown empty — nothing is filled in on its behalf.
| MRC | Requirement | Value |
|---|---|---|
| AAQL | BODY STYLE | |
| CWBH | SHAFT NOMINAL THREAD SIZE | SINGLE SHAFT INCHES 0.190 |
| TEST | TEST DATA DOCUMENT | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--IL-S-20708 |
| AJYY | SHAFT THREAD SERIES DESIGNATOR | SINGLE SHAFT UNF |
| ZZZK | SPECIFICATION/STANDARD DATA | GOVERNMENT SPECIFICATION 81349--IL-S-20708 TO 8 |
| AJST | ROTOR INPUT CURRENT RATING | MILLIAMPERES MAXIMUM 130.0 |
| AJSV | ROTOR INPUT ELECTRICAL POWER RATING | MILLIWATTS NOMINAL 340.0 |
| CQWQ | SHAFT THREAD LENGTH | SINGLE SHAFT INCHES NOMINAL 0.1900 |
| CRSJ | SHAFT TYPE | SINGLE SHAFT SPLINE W/THREADS |
| CRSY | ALIGNMENT HOLE DEPTH | INCHES MINIMUM 0.1250 |
| CSJY | TRANSFORMATION RATIO | ROTOR TO STATOR NOMINAL 0.454 |
| TTQY | TERMINAL TYPE AND QUANTITY | SCREW 5 |
| AJVH | MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 19.00 |
| AJVL | ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -7.0 TO 7.0 |
| AJVM | SPLINE TOOTH QUANTITY | 21 |
| AJVV | TORQUE GRADIENT PER ANGULAR DEG | INCH-OUNCES MAXIMUM 0.070 |
| AJVW | ALIGNMENT HOLE QUANTITY | 4 |
| AJWQ | PILOT LENGTH | INCHES NOMINAL 0.0620 |
| AAVL | PILOT DIAMETER | INCHES MINIMUM 0.6245 AND INCHES MAXIMUM 0.6250 |
| ABHP | OVERALL LENGTH | INCHES NOMINAL 2.3560 |
| ABKK | FLANGE DIAMETER | INCHES MINIMUM 1.0570 AND INCHES MAXIMUM 1.0620 |
| AKAF | SHAFT THREAD DIRECTION | SINGLE SHAFT RIGHT-HAND |
| AKAN | SHAFT THREAD CLASS | 2A |
| CQRG | BODY MATERIAL | STEEL CORROSION RESISTING |
| CQTM | TERMINAL LOCATION | REAR |
| CTCW | ALIGNMENT HOLE BOLT CIRCLE DIAMETER | INCHES NOMINAL 0.8120 |
| AJWX | MOUNTING SURFACE TO TERMINAL END DISTANCE | INCHES NOMINAL 2.3560 |
| AJXA | SPLINE TOOTH DIAMETRAL PITCH | 120 |
| AJTG | ZRO IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 200.00 AND MAXIMUM 300.00 |
| AJTH | ZRO IMPEDANCE ANGLE IN DEG | MINIMUM 80.50 AND MAXIMUM 84.00 |
| AJTN | ZSS IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 6.00 AND MAXIMUM 12.00 |
| AJTP | ZSS IMPEDANCE ANGLE IN DEG | MINIMUM 18.00 AND MAXIMUM 30.00 |
| AJVF | PHASE SHIFT ANGLE IN DEG | INPUT TO OUTPUT MAXIMUM 4.000 |
| AJVG | MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | OUTPUT 12.00 |
| AJSR | ROTOR INPUT VOLTAGE RATING IN VOLTS | NOMINAL 26.0 |
| AJSS | FREQUENCY IN HERTZ | NOMINAL 400.0 |
| ABKU | FLANGE THICKNESS | INCHES NOMINAL 0.0930 |
| ABPA | UNDERCUT DIAMETER | INCHES NOMINAL 0.9750 |
| ABPC | UNDERCUT WIDTH | INCHES NOMINAL 0.0620 |
| ABRY | LENGTH | SHOULDER INCHES NOMINAL 0.0620 |
| ABWV | SHAFT DIAMETER | SINGLE SHAFT INCHES MINIMUM 0.1870 AND INCHES MAXIMUM 0.1872 |
| ABXF | SHAFT LENGTH | SINGLE SHAFT INCHES NOMINAL 0.5620 |
| AFJN | FRAGILITY FACTOR | MODERATELY RUGGED |
| AHCG | MAXIMUM TEMP RISE | CELSIUS 20.0 |
| AJSL | BODY SIZE | 11 |
| AAVH | SHOULDER DIAMETER | INCHES MINIMUM 0.9995 AND INCHES MAXIMUM 1.0000 |
Supersedes
This item replaces cancelled NIINs 007242607 · 008598702 · 009493483 · 010151092 · 012690592. An older drawing citing one of those numbers resolves here.