NSN 5990-00-099-0700 · NIIN 000990700 · FSC 5990
NO DASHES 5990000990700
In Stock
RESOLVER,ELECTRICAL
Synchros and Resolvers
Technical characteristics
43 rows
Straight from the federal item record. Entries the record leaves empty are shown empty — nothing is filled in on its behalf.
| MRC | Requirement | Value |
|---|---|---|
| AAVH | SHOULDER DIAMETER | INCHES MINIMUM 0.9995 AND INCHES MAXIMUM 1.0000 |
| AAVL | PILOT DIAMETER | INCHES MINIMUM 0.6245 AND INCHES MAXIMUM 0.6250 |
| AJXA | SPLINE TOOTH DIAMETRAL PITCH | 120 |
| AJYY | SHAFT THREAD SERIES DESIGNATOR | SINGLE SHAFT UNF |
| AKAF | SHAFT THREAD DIRECTION | SINGLE SHAFT RIGHT-HAND |
| AKAN | SHAFT THREAD CLASS | 2A |
| CQTM | TERMINAL LOCATION | REAR |
| CQWQ | SHAFT THREAD LENGTH | SINGLE SHAFT INCHES NOMINAL 0.2550 |
| CRSJ | SHAFT TYPE | SINGLE SHAFT ROUND, THREADED |
| CRSY | ALIGNMENT HOLE DEPTH | INCHES NOMINAL 0.1250 |
| CSJY | TRANSFORMATION RATIO | ROTOR TO STATOR NOMINAL 0.497 |
| CTCW | ALIGNMENT HOLE BOLT CIRCLE DIAMETER | INCHES MINIMUM 0.8090 AND INCHES MAXIMUM 0.8150 |
| CWBH | SHAFT NOMINAL THREAD SIZE | SINGLE SHAFT INCHES 0.190 |
| MATT | MATERIAL | BODY STEEL CORROSION RESISTING |
| AAQL | BODY STYLE | |
| AJWX | MOUNTING SURFACE TO TERMINAL END DISTANCE | INCHES MINIMUM 2.3340 AND INCHES MAXIMUM 2.3540 |
| TEST | TEST DATA DOCUMENT | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--IL-R-23417 |
| TTQY | TERMINAL TYPE AND QUANTITY | SCREW 7 |
| ZZZK | SPECIFICATION/STANDARD DATA | GOVERNMENT SPECIFICATION 81349--IL-R-23417 TO 25 |
| AJSR | ROTOR INPUT VOLTAGE RATING IN VOLTS | NOMINAL 9.0 |
| AJSS | FREQUENCY IN HERTZ | NOMINAL 4000.0 |
| AJST | ROTOR INPUT CURRENT RATING | MILLIAMPERES NOMINAL 2.6 |
| AJSV | ROTOR INPUT ELECTRICAL POWER RATING | MILLIWATTS NOMINAL 10.0 |
| AJSW | ZRO RESISTANCE IN OHMS | MINIMUM 3720.00 AND MAXIMUM 4467.00 |
| AJTC | ZSS RESISTANCE IN OHMS | MINIMUM 121.00 AND MAXIMUM 145.00 |
| AJTG | ZRO IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 68.00 AND MAXIMUM 73.00 |
| AJTN | ZSS IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 65.00 AND MAXIMUM 69.00 |
| AJVG | MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | OUTPUT 15.00 |
| AJVH | MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 20.00 |
| AJVJ | INTERAXIS ERROR ANGULAR RANGE IN MINUTES | -7.0 TO 7.0 |
| AJVM | SPLINE TOOTH QUANTITY | 21 |
| AJVW | ALIGNMENT HOLE QUANTITY | 4 |
| AJWQ | PILOT LENGTH | INCHES NOMINAL 0.0620 |
| ABHP | OVERALL LENGTH | INCHES MAXIMUM 2.4130 |
| ABKK | FLANGE DIAMETER | INCHES MINIMUM 1.0570 AND INCHES MAXIMUM 1.0650 |
| ABKU | FLANGE THICKNESS | INCHES NOMINAL 0.0930 |
| ABPA | UNDERCUT DIAMETER | INCHES MINIMUM 0.9745 AND INCHES MAXIMUM 0.9750 |
| ABPC | UNDERCUT WIDTH | INCHES NOMINAL 0.0500 |
| ABRY | LENGTH | SHOULDER INCHES NOMINAL 0.0620 |
| ABWV | SHAFT DIAMETER | SINGLE SHAFT INCHES NOMINAL 0.1900 |
| ABXF | SHAFT LENGTH | SINGLE SHAFT INCHES MINIMUM 0.5450 AND INCHES MAXIMUM 0.5650 |
| AHCG | MAXIMUM TEMP RISE | CELSIUS 85.0 |
| AJSL | BODY SIZE | 11 |
Supersedes
This item replaces cancelled NIIN 000423414. An older drawing citing one of those numbers resolves here.