NSN 5990-00-018-9719 · NIIN 000189719 · FSC 5990
NO DASHES 5990000189719
In Stock
SYNCHRO,DIFFERENTIAL TRANSMITTER
Synchros and Resolvers
Technical characteristics
45 rows
Straight from the federal item record. Entries the record leaves empty are shown empty — nothing is filled in on its behalf.
| MRC | Requirement | Value |
|---|---|---|
| AJXA | SPLINE TOOTH DIAMETRAL PITCH | 120 |
| AJYY | SHAFT THREAD SERIES DESIGNATOR | SINGLE SHAFT UNF |
| AKAF | SHAFT THREAD DIRECTION | SINGLE SHAFT RIGHT-HAND |
| AKAN | SHAFT THREAD CLASS | 2A |
| CQRG | BODY MATERIAL | STEEL CORROSION RESISTING |
| CQTM | TERMINAL LOCATION | REAR |
| CQWQ | SHAFT THREAD LENGTH | SINGLE SHAFT INCHES NOMINAL 0.2000 |
| CRSJ | SHAFT TYPE | SINGLE SHAFT ROUND, SLOTTED |
| CRSY | ALIGNMENT HOLE DEPTH | INCHES MINIMUM 0.1250 |
| CSJY | TRANSFORMATION RATIO | ROTOR TO STATOR NOMINAL 1.154 |
| CTCW | ALIGNMENT HOLE BOLT CIRCLE DIAMETER | INCHES NOMINAL 1.2500 |
| CWBH | SHAFT NOMINAL THREAD SIZE | SINGLE SHAFT INCHES 0.190 |
| TEST | TEST DATA DOCUMENT | SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). 81349--IL-S-20708 |
| TTQY | TERMINAL TYPE AND QUANTITY | SCREW 5 |
| ZZZK | SPECIFICATION/STANDARD DATA | GOVERNMENT SPECIFICATION 81349--IL-S-20708 TO 30 |
| AJSQ | STATOR INPUT ELECTRICAL POWER RATING | MILLIWATTS NOMINAL 950.0 |
| AJSS | FREQUENCY IN HERTZ | NOMINAL 400.0 |
| AJTJ | ZSO IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 610.00 AND MAXIMUM 785.00 |
| AJTK | ZSO IMPEDANCE ANGLE IN DEG | MINIMUM 83.00 AND MAXIMUM 86.50 |
| AJTL | ZRS IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 76.00 AND MAXIMUM 110.00 |
| AJTM | ZRS IMPEDANCE ANGLE IN DEG | MINIMUM 40.00 AND MAXIMUM 55.00 |
| AJVF | PHASE SHIFT ANGLE IN DEG | INPUT TO OUTPUT NOMINAL 2.000 |
| AJVG | MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | OUTPUT 40.00 |
| AJVH | MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 75.00 |
| AJVL | ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -6.0 TO 6.0 |
| AJVM | SPLINE TOOTH QUANTITY | 21 |
| AJVV | TORQUE GRADIENT PER ANGULAR DEG | INCH-OUNCES MAXIMUM 0.100 |
| AJVW | ALIGNMENT HOLE QUANTITY | 4 |
| ABKK | FLANGE DIAMETER | INCHES MINIMUM 1.7450 AND INCHES MAXIMUM 1.7500 |
| ABKU | FLANGE THICKNESS | INCHES NOMINAL 0.0930 |
| ABPA | UNDERCUT DIAMETER | INCHES NOMINAL 1.6250 |
| ABPC | UNDERCUT WIDTH | INCHES NOMINAL 0.0780 |
| ABRY | LENGTH | SHOULDER INCHES NOMINAL 0.1320 |
| ABWV | SHAFT DIAMETER | SINGLE SHAFT INCHES MINIMUM 0.1870 AND INCHES MAXIMUM 0.1872 |
| ABXF | SHAFT LENGTH | SINGLE SHAFT INCHES NOMINAL 0.5400 |
| AHCG | MAXIMUM TEMP RISE | CELSIUS 20.0 |
| AJSL | BODY SIZE | 18 |
| AJSN | STATOR INPUT VOLTAGE RATING IN VOLTS | NOMINAL 90.0 |
| AJSP | STATOR INPUT CURRENT RATING | MILLIAMPERES MAXIMUM 128.0 |
| ABHP | OVERALL LENGTH | INCHES NOMINAL 3.2100 |
| AJWQ | PILOT LENGTH | INCHES NOMINAL 0.0400 |
| AJWX | MOUNTING SURFACE TO TERMINAL END DISTANCE | INCHES NOMINAL 2.6700 |
| AAQL | BODY STYLE | |
| AAVH | SHOULDER DIAMETER | INCHES MINIMUM 1.5615 AND INCHES MAXIMUM 1.5620 |
| AAVL | PILOT DIAMETER | INCHES MINIMUM 0.9370 AND INCHES MAXIMUM 0.9375 |
Supersedes
This item replaces cancelled NIIN 004671936. An older drawing citing one of those numbers resolves here.