NSN 5990-00-922-2449 · NIIN 009222449 · FSC 5990
NO DASHES 5990009222449
In Stock
SYNCHRO,TRANSMITTER
Synchros and Resolvers
Technical characteristics
35 rows
Straight from the federal item record. Entries the record leaves empty are shown empty — nothing is filled in on its behalf.
| MRC | Requirement | Value |
|---|---|---|
| ABKK | FLANGE DIAMETER | INCHES MINIMUM 1.0570 AND INCHES MAXIMUM 1.0620 |
| ABPC | UNDERCUT WIDTH | INCHES NOMINAL 0.0500 |
| AJSR | ROTOR INPUT VOLTAGE RATING IN VOLTS | MINIMUM 114.0 AND MAXIMUM 116.0 |
| AAVH | SHOULDER DIAMETER | INCHES MINIMUM 0.9995 AND INCHES MAXIMUM 1.0000 |
| AAVL | PILOT DIAMETER | INCHES MINIMUM 0.6245 AND INCHES MAXIMUM 0.6250 |
| ABHP | OVERALL LENGTH | INCHES NOMINAL 2.3560 |
| AAQL | BODY STYLE | |
| AJTG | ZRO IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 3720.00 AND MAXIMUM 4700.00 |
| AJTH | ZRO IMPEDANCE ANGLE IN DEG | MINIMUM 80.00 AND MAXIMUM 84.00 |
| ABRY | LENGTH | SHOULDER INCHES NOMINAL 0.0620 |
| AJVF | PHASE SHIFT ANGLE IN DEG | INPUT TO OUTPUT MINIMUM 3.000 AND INPUT TO OUTPUT MAXIMUM 6.000 |
| AJVG | MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | OUTPUT 45.00 |
| ABKU | FLANGE THICKNESS | INCHES NOMINAL 0.0930 |
| AFJN | FRAGILITY FACTOR | MODERATELY RUGGED |
| AHCG | MAXIMUM TEMP RISE | CELSIUS 20.0 |
| AJWQ | PILOT LENGTH | INCHES NOMINAL 0.0620 |
| AJWX | MOUNTING SURFACE TO TERMINAL END DISTANCE | INCHES NOMINAL 1.7320 |
| CQTM | TERMINAL LOCATION | REAR |
| CRSJ | SHAFT TYPE | SINGLE SHAFT ROUND |
| CRSY | ALIGNMENT HOLE DEPTH | INCHES NOMINAL 0.1250 |
| AJSL | BODY SIZE | 11 |
| AJTP | ZSS IMPEDANCE ANGLE IN DEG | MINIMUM 17.00 AND MAXIMUM 26.00 |
| ABXF | SHAFT LENGTH | SINGLE SHAFT INCHES NOMINAL 0.5000 |
| AJVH | MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 75.00 |
| CSJY | TRANSFORMATION RATIO | STATOR TO ROTOR NOMINAL 0.783 |
| CTCW | ALIGNMENT HOLE BOLT CIRCLE DIAMETER | INCHES MINIMUM 0.8090 AND INCHES MAXIMUM 0.8150 |
| TEST | TEST DATA DOCUMENT | DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) 18876-10181799 |
| TTQY | TERMINAL TYPE AND QUANTITY | SCREW 5 |
| AJVW | ALIGNMENT HOLE QUANTITY | 4 |
| AJSS | FREQUENCY IN HERTZ | MINIMUM 396.0 AND MAXIMUM 404.0 |
| AJST | ROTOR INPUT CURRENT RATING | MILLIAMPERES NOMINAL 31.0 |
| AJSV | ROTOR INPUT ELECTRICAL POWER RATING | MILLIWATTS NOMINAL 490.0 |
| AJVT | ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS | INCH-OUNCES NOMINAL 0.07 |
| ABWV | SHAFT DIAMETER | SINGLE SHAFT INCHES MINIMUM 0.1867 AND INCHES MAXIMUM 0.1872 |
| AJTN | ZSS IMPEDANCE MAGNITUDE IN OHMS | MINIMUM 410.00 AND MAXIMUM 500.00 |
Supersedes
This item replaces cancelled NIIN 000366460. An older drawing citing one of those numbers resolves here.